KN05 V2.1k >>boot delo V0.7 Copyright 2000 Florian Lohoff Loading /etc/delo.conf .. ok Loading /boot/vmlinux-2.4.18 ....... ok This DECstation is a DS5000/2x0 CPU revision is: 00000440 FPU revision is: 00000500 Primary instruction cache 16kb, linesize 16 bytes. Primary data cache 16kb, linesize 16 bytes. Secondary cache sized at 1024K linesize 32 bytes. Linux version 2.4.18 (root@elrond) (gcc version 2.96 20000731 (Red Hat Linux 7.3 2.96-110.1)) #14 Fri Jul 19 16:42:48 MEST 2002 Determined physical RAM map: memory: 10000000 @ 00000000 (usable) On node 0 totalpages: 65536 zone(0): 65536 pages. zone(1): 0 pages. zone(2): 0 pages. Kernel command line: root=/dev/sda1 console=ttyS2 ro Calibrating delay loop... 59.86 BogoMIPS Memory: 255556k/262144k available (1816k kernel code, 6588k reserved, 108k data, 76k init, 0k highmem) Dentry-cache hash table entries: 32768 (order: 6, 262144 bytes) Inode-cache hash table entries: 16384 (order: 5, 131072 bytes) Mount-cache hash table entries: 4096 (order: 3, 32768 bytes) Buffer-cache hash table entries: 16384 (order: 4, 65536 bytes) Page-cache hash table entries: 65536 (order: 6, 262144 bytes) Checking for 'wait' instruction... unavailable. POSIX conformance testing by UNIFIX TURBOchannel rev. 1 at 25.0 MHz (without parity) slot 1: DEC PMAZ-AA V5.3d Linux NET4.0 for Linux 2.4 Based upon Swansea University Computer Society NET3.039 Initializing RT netlink socket Starting kswapd Journalled Block Device driver loaded devfs: v1.10 (20020120) Richard Gooch (rgooch@atnf.csiro.au) devfs: boot_options: 0x0 lk201: DECstation LK keyboard driver v0.05. pty: 256 Unix98 ptys configured DECstation Z8530 serial driver version 0.07 ttyS00 at 0xbf900001 (irq = 14) is a Z85C30 SCC ttyS01 at 0xbf900009 (irq = 14) is a Z85C30 SCC ttyS02 at 0xbf980001 (irq = 15) is a Z85C30 SCC rtc: Digital DECstation epoch (2000) detected Real Time Clock Driver v1.10e block: 128 slots per queue, batch=32 declance.c: v0.009 by Linux MIPS DECstation task force eth0: IOASIC onboard LANCE, addr = 08:00:2b:37:63:76, irq = 16 SCSI subsystem driver Revision: 1.00 SCSI ID 7 Clk 25MHz CCF=5 TOut 167 NCR53C9x(esp236) SCSI ID 7 Clk 25MHz CCF=5 TOut 167 NCR53C9x(esp236) ESP: Total of 2 ESP hosts found, 2 actually in use. scsi0 : ESP236 (NCR53C9x) scsi1 : ESP236 (NCR53C9x) esp0: AIEEE wide msg received esp0: hoping for msgout Vendor: IBM Model: DCHS04U Rev: 6464 Type: Direct-Access ANSI SCSI revision: 02 Vendor: COMPAQ Model: C2490A Rev: 5193 Type: Direct-Access ANSI SCSI revision: 02 Vendor: COMPAQ Model: C2490A Rev: 5193 Type: Direct-Access ANSI SCSI revision: 02 Vendor: COMPAQ Model: C2490A Rev: 5193 Type: Direct-Access ANSI SCSI revision: 02 Vendor: COMPAQ Model: C2490A Rev: 5193 Type: Direct-Access ANSI SCSI revision: 02 Vendor: COMPAQ Model: C2490A Rev: 5193 Type: Direct-Access ANSI SCSI revision: 02 Vendor: SONY Model: CD-ROM CDU-55S Rev: 1.0t Type: CD-ROM ANSI SCSI revision: 02 Attached scsi disk sda at scsi0, channel 0, id 0, lun 0 Attached scsi disk sdb at scsi1, channel 0, id 1, lun 0 Attached scsi disk sdc at scsi1, channel 0, id 2, lun 0 Attached scsi disk sdd at scsi1, channel 0, id 3, lun 0 Attached scsi disk sde at scsi1, channel 0, id 4, lun 0 Attached scsi disk sdf at scsi1, channel 0, id 5, lun 0 SCSI device sda: 8813870 512-byte hdwr sectors (4513 MB) Partition check: /dev/scsi/host0/bus0/target0/lun0: p1 p2 p3 esp1: target 1 [period 200ns offset 8 5.00MHz synchronous SCSI] SCSI device sdb: 4110000 512-byte hdwr sectors (2104 MB) /dev/scsi/host1/bus0/target1/lun0: p1 esp1: target 2 [period 200ns offset 8 5.00MHz synchronous SCSI] SCSI device sdc: 4110000 512-byte hdwr sectors (2104 MB) /dev/scsi/host1/bus0/target2/lun0: p1 esp1: target 3 [period 200ns offset 8 5.00MHz synchronous SCSI] SCSI device sdd: 4110000 512-byte hdwr sectors (2104 MB) /dev/scsi/host1/bus0/target3/lun0: p1 esp1: target 4 [period 200ns offset 8 5.00MHz synchronous SCSI] SCSI device sde: 4110000 512-byte hdwr sectors (2104 MB) /dev/scsi/host1/bus0/target4/lun0: p1 esp1: target 5 [period 200ns offset 8 5.00MHz synchronous SCSI] SCSI device sdf: 4110000 512-byte hdwr sectors (2104 MB) /dev/scsi/host1/bus0/target5/lun0: p1 Attached scsi CD-ROM sr0 at scsi1, channel 0, id 6, lun 0 esp1: target 6 [period 248ns offset 15 4.03MHz synchronous SCSI] sr0: scsi-1 drive Uniform CD-ROM driver Revision: 3.12 NET4: Linux TCP/IP 1.0 for NET4.0 IP Protocols: ICMP, UDP, TCP, IGMP IP: routing cache hash table of 2048 buckets, 16Kbytes TCP: Hash tables configured (established 16384 bind 16384) NET4: Unix domain sockets 1.0/SMP for Linux NET4.0. kjournald starting. Commit interval 5 seconds EXT3-fs: mounted filesystem with ordered data mode. VFS: Mounted root (ext3 filesystem) readonly. Freeing unused PROM memory: 124k freed Freeing unused kernel memory: 76k freed INIT: version 2.84 booting Welcome to Red Hat Linux Press 'I' to enter interactive startup. Mounting proc filesystem: [ OK ] Configuring kernel parameters: [ OK ] Setting clock (utc): Tue Jul 23 16:44:53 MEST 2002 [ OK ] Activating swap partitions: [ OK ] Setting hostname elrond: [ OK ] Checking root filesystem /dev/sda1: clean, 17644/65792 files, 53927/131072 blocks [/sbin/fsck.ext3 (1) -- /] fsck.ext3 -a /dev/sda1 [ OK ] Remounting root filesystem in read-write mode: [ OK ] Finding module dependencies: [ OK ] Starting up RAID devices: md0 Checking filesystems /dev/sda3: clean, 134631/468640 files, 581462/936130 blocks /dev/md0: clean, 116823/1028160 files, 468224/2053184 blocks Checking all file systems. [/sbin/fsck.ext3 (1) -- /usr] fsck.ext3 -a /dev/sda3 [/sbin/fsck.ext3 (1) -- /local1] fsck.ext3 -a /dev/md0 [ OK ] Mounting local filesystems: [ OK ] Enabling swap space: [ OK ] INIT: Entering runlevel: 3 Entering non-interactive startup Setting network parameters: [ OK ] Bringing up loopback interface: [ OK ] Bringing up interface eth0: [ OK ] Starting system logger: [ OK ] Starting kernel logger: [ OK ] Starting portmapper: [ OK ] Initializing random number generator: [ OK ] Mounting other filesystems: [ OK ] ntpd: Synchronizing with time server: [ OK ] Starting ntpd: [ OK ] Starting automounter:[ OK ] Starting atd: [ OK ] Starting sshd: [ OK ] Starting xinetd: [ OK ] Starting NFS services: [ OK ] Starting NFS daemon: [ OK ] Starting NFS mountd: [ OK ] Starting NFS file locking services: Starting NFS lockd: [ OK ] Starting NFS statd: [ OK ] Starting dhcpd: [ OK ] Starting crond: [ OK ] Starting anacron: [ OK ] Starting cupsd: [ OK ] Red Hat Linux release 7.3 (Valhalla) Kernel 2.4.18 on an mips elrond login: