KN05 V2.1k >>boot 3/tftp console=ttyS2 ip=bootp root=/dev/nfs single rw -tftp boot(3), bootp|139.63.1.7:/tftpboot/vmlinux.ecoff/ -tftp load 2015232+0+172944 This DECstation is a DS5000/2x0 CPU revision is: 00000440 FPU revision is: 00000500 Primary instruction cache 16kb, linesize 16 bytes. Primary data cache 16kb, linesize 16 bytes. Secondary cache sized at 1024K linesize 32 bytes. TLB has 48 entries. Linux version 2.4.16 (root@elrond) (gcc version 2.96 20000731 (Red Hat Linux 7.1 2.96-96.1)) #2 Fri Dec 14 21:02:51 MET 2001 Determined physical RAM map: memory: 10000000 @ 00000000 (usable) On node 0 totalpages: 65536 zone(0): 65536 pages. zone(1): 0 pages. zone(2): 0 pages. Kernel command line: console=ttyS2 ip=bootp root=/dev/nfs single rw Calibrating delay loop... 59.86 BogoMIPS Memory: 255608k/262144k available (1806k kernel code, 6536k reserved, 87k data, 72k init) Dentry-cache hash table entries: 32768 (order: 6, 262144 bytes) Inode-cache hash table entries: 16384 (order: 5, 131072 bytes) Mount-cache hash table entries: 4096 (order: 3, 32768 bytes) Buffer-cache hash table entries: 16384 (order: 4, 65536 bytes) Page-cache hash table entries: 65536 (order: 6, 262144 bytes) Checking for 'wait' instruction... unavailable. POSIX conformance testing by UNIFIX TURBOchannel rev. 1 at 25.0 MHz (without parity) slot 1: DEC PMAZ-AA V5.3d Linux NET4.0 for Linux 2.4 Based upon Swansea University Computer Society NET3.039 Initializing RT netlink socket Starting kswapd Journalled Block Device driver loaded devfs: v0.120 (20011103) Richard Gooch (rgooch@atnf.csiro.au) devfs: boot_options: 0x0 pty: 256 Unix98 ptys configured DECstation Z8530 serial driver version 0.05 DECstation LK keyboard driver v0.04... LK401 detected ttyS00 at 0xbf900001 (irq = 4) is a Z85C30 SCC ttyS01 at 0xbf900009 (irq = 4) is a Z85C30 SCC ttyS02 at 0xbf980001 (irq = 4) is a Z85C30 SCC rtc: Digital DECstation epoch (2000) detected Real Time Clock Driver v1.10e block: 128 slots per queue, batch=32 declance.c: v0.008 by Linux Mips DECstation task force eth0: IOASIC onboard LANCE, addr = 08:00:2b:37:63:76, irq = 3 SCSI subsystem driver Revision: 1.00 SCSI ID 7 Clk 25MHz CCF=5 TOut 167 NCR53C9x(esp236) SCSI ID 7 Clk 25MHz CCF=5 TOut 167 NCR53C9x(esp236) ESP: Total of 2 ESP hosts found, 2 actually in use. scsi0 : ESP236 (NCR53C9x) scsi1 : ESP236 (NCR53C9x) esp0: AIEEE wide msg received esp0: hoping for msgout Vendor: IBM Model: DCHS Rev: 64 Type: Direct-Access ANSI SCSI revision: 02 Vendor: DEC Model: RZ58 (C) DEC Rev: 3000 Type: Direct-Access ANSI SCSI revision: 02 Vendor: SONY Model: CD-ROM CDU-55S Rev: 1.0t Type: CD-ROM ANSI SCSI revision: 02 Attached scsi disk sda at scsi0, channel 0, id 0, lun 0 Attached scsi disk sdb at scsi0, channel 0, id 1, lun 0 sda: Spinning up disk........................ready SCSI device sda: 8813870 512-byte hdwr sectors (4513 MB) Partition check: /dev/scsi/host0/bus0/target0/lun0: p1 p2 p3 esp0: target 1 [period 200ns offset 15 5.00MHz synchronous SCSI] SCSI device sdb: 2698061 512-byte hdwr sectors (1381 MB) /dev/scsi/host0/bus0/target1/lun0: p1 p2 p3 p4 p5 Attached scsi CD-ROM sr0 at scsi0, channel 0, id 6, lun 0 esp0: target 6 [period 248ns offset 15 4.03MHz synchronous SCSI] sr0: scsi-1 drive Uniform CD-ROM driver Revision: 3.12 NET4: Linux TCP/IP 1.0 for NET4.0 IP Protocols: ICMP, UDP, TCP, IGMP IP: routing cache hash table of 2048 buckets, 16Kbytes TCP: Hash tables configured (established 16384 bind 16384) Sending BOOTP requests . OK IP-Config: Got BOOTP answer from 139.63.1.7, my address is 139.63.1.12 IP-Config: Complete: device=eth0, addr=139.63.1.12, mask=255.255.255.0, gw=139.63.1.11, host=elrond, domain=, nis-domain=(none), bootserver=139.63.1.7, rootserver=139.63.1.7, rootpath=/export/mips-new NET4: Unix domain sockets 1.0/SMP for Linux NET4.0. Looking up port of RPC 100003/2 on 139.63.1.7 Looking up port of RPC 100005/1 on 139.63.1.7 VFS: Mounted root (nfs filesystem). Freeing unused PROM memory: 124k freed Freeing unused kernel memory: 72k freed INIT: version 2.78 booting Welcome to Red Hat Linux Press 'I' to enter interactive startup. Mounting proc filesystem: [ OK ] Configuring kernel parameters: [ OK ] Setting clock (utc): Mon Dec 24 11:06:13 MET 2001 [ OK ] Activating swap partitions: [ OK ] Setting hostname localhost: [ OK ] Remounting root filesystem in read-write mode: [ OK ] Checking filesystems Checking all file systems. [ OK ] Mounting local filesystems: [ OK ] Enabling swap space: [ OK ] INIT: Entering runlevel: 3 Entering non-interactive startup Setting network parameters: [ OK ] Bringing up interface lo: [ OK ] Bringing up interface eth0: [ OK ] Starting system logger: [ OK ] Starting kernel logger: [ OK ] Starting portmapper: [ OK ] Starting keytable: [ OK ] Initializing random number generator: [ OK ] Mounting NFS filesystems: [ OK ] Mounting other filesystems: [ OK ] Starting xinetd: [ OK ] Starting crond: [ OK ] Red Hat Linux release 7.1 (Seawolf) Kernel 2.4.16 on a mips localhost login: