KN04 V2.1k >>boot delo V0.7 Copyright 2000 Florian Lohoff Loading /etc/delo.conf .. ok Loading /boot/vmlinux ..................... ok This DECstation is a DS5000/1xx CPU revision is: 00000430 FPU revision is: 00000500 Primary instruction cache 8kb, linesize 16 bytes. Primary data cache 8kb, linesize 16 bytes. Secondary cache sized at 1024K linesize 32 bytes. TLB has 48 entries. Linux version 2.4.16 (root@harald.research.kpn.com) (gcc version 2.96 20000731 (Red Hat Linux 7.1 2.96-99.1)) #1 Mon Dec 17 14:20:19 MET 2001 Determined physical RAM map: memory: 02000000 @ 00000000 (usable) On node 0 totalpages: 8192 zone(0): 8192 pages. zone(1): 0 pages. zone(2): 0 pages. Kernel command line: root=/dev/sdc1 console=ttyS2 Calibrating delay loop... 49.88 BogoMIPS Memory: 29908k/32768k available (1715k kernel code, 2860k reserved, 87k data, 76k init) Dentry-cache hash table entries: 4096 (order: 3, 32768 bytes) Inode-cache hash table entries: 2048 (order: 2, 16384 bytes) Mount-cache hash table entries: 512 (order: 0, 4096 bytes) Buffer-cache hash table entries: 1024 (order: 0, 4096 bytes) Page-cache hash table entries: 8192 (order: 3, 32768 bytes) Checking for 'wait' instruction... unavailable. POSIX conformance testing by UNIFIX TURBOchannel rev. 1 at 12.5 MHz (without parity) Linux NET4.0 for Linux 2.4 Based upon Swansea University Computer Society NET3.039 Initializing RT netlink socket Starting kswapd devfs: v0.120 (20011103) Richard Gooch (rgooch@atnf.csiro.au) devfs: boot_options: 0x0 pty: 256 Unix98 ptys configured DECstation Z8530 serial driver version 0.05 DECstation LK keyboard driver v0.04... LK401 detected ttyS00 at 0xbc100001 (irq = 4) is a Z85C30 SCC ttyS01 at 0xbc100009 (irq = 4) is a Z85C30 SCC ttyS02 at 0xbc180001 (irq = 4) is a Z85C30 SCC rtc: Digital DECstation epoch (2000) detected Real Time Clock Driver v1.10e block: 64 slots per queue, batch=16 RAMDISK driver initialized: 16 RAM disks of 4096K size 1024 blocksize loop: loaded (max 8 devices) declance.c: v0.008 by Linux Mips DECstation task force eth0: IOASIC onboard LANCE, addr = 08:00:2b:26:47:f0, irq = 3 SCSI subsystem driver Revision: 1.00 SCSI ID 7 Clk 25MHz CCF=5 TOut 167 NCR53C9x(esp236) ESP: Total of 1 ESP hosts found, 1 actually in use. scsi0 : ESP236 (NCR53C9x) esp0: hoping for msgout Vendor: DEC Model: RZ56 (C) DEC Rev: 0400 Type: Direct-Access ANSI SCSI revision: 01 CCS Vendor: DEC Model: RZ25 (C) DEC Rev: 0700 Type: Direct-Access ANSI SCSI revision: 02 Vendor: SEAGATE Model: ST12400N SUN2.1G Rev: 8720 Type: Direct-Access ANSI SCSI revision: 02 Attached scsi disk sda at scsi0, channel 0, id 0, lun 0 Attached scsi disk sdb at scsi0, channel 0, id 1, lun 0 Attached scsi disk sdc at scsi0, channel 0, id 2, lun 0 sda: Spinning up disk..................ready SCSI device sda: 1299174 512-byte hdwr sectors (665 MB) Partition check: /dev/scsi/host0/bus0/target0/lun0: p1 p2 p3 p4 esp0: target 1 [period 200ns offset 15 5.00MHz synchronous SCSI] sdb: Spinning up disk.............ready SCSI device sdb: 832527 512-byte hdwr sectors (426 MB) /dev/scsi/host0/bus0/target1/lun0: p1 p2 esp0: target 2 [period 200ns offset 15 5.00MHz synchronous SCSI] SCSI device sdc: 4194685 512-byte hdwr sectors (2148 MB) /dev/scsi/host0/bus0/target2/lun0: p1 p2 NET4: Linux TCP/IP 1.0 for NET4.0 IP Protocols: ICMP, UDP, TCP, IGMP IP: routing cache hash table of 512 buckets, 4Kbytes TCP: Hash tables configured (established 2048 bind 2048) NET4: Unix domain sockets 1.0/SMP for Linux NET4.0. VFS: Mounted root (ext2 filesystem) readonly. Freeing unused PROM memory: 124k freed Freeing unused kernel memory: 76k freed INIT: version 2.78 booting Welcome to Red Hat Linux Press 'I' to enter interactive startup. Mounting proc filesystem: [ OK ] Configuring kernel parameters: [ OK ] Setting clock (utc): Thu Dec 20 08:35:45 MET 2001 [ OK ] Activating swap partitions: [ OK ] Setting hostname harald.research.kpn.com: [ OK ] Checking root filesystem /dev/sdc1: clean, 49499/489472 files, 531157/1952349 blocks [/sbin/fsck.ext2 -- /] fsck.ext2 -a /dev/sdc1 [ OK ] Remounting root filesystem in read-write mode: [ OK ] Finding module dependencies: [ OK ] Checking filesystems Checking all file systems. [ OK ] Mounting local filesystems: [ OK ] Enabling swap space: [ OK ] INIT: Entering runlevel: 3 Entering non-interactive startup Setting network parameters: [ OK ] Bringing up interface lo: [ OK ] Bringing up interface eth0: [ OK ] Starting system logger: [ OK ] Starting kernel logger: [ OK ] Starting portmapper: [ OK ] Starting keytable: [ OK ] Initializing random number generator: [ OK ] Mounting other filesystems: [ OK ] Starting automounter:[ OK ] Starting atd: [ OK ] Starting sshd: [ OK ] Starting xinetd: [ OK ] Starting NFS file locking services: Starting NFS lockd: [ OK ] Starting NFS statd: [ OK ] Starting crond: [ OK ] Starting anacron: [ OK ] Red Hat Linux release 7.1 (Seawolf) Kernel 2.4.16 on a mips